Difference between revisions of "EK-TM4C123GXL LaunchPad Initial Board Setup"
From EdWiki
m |
m (→Connecting the board) |
||
Line 8: | Line 8: | ||
===Connecting the board=== | ===Connecting the board=== | ||
− | [[image:tm4c123gxl_board_setup.png| | + | [[image:tm4c123gxl_board_setup.png|center]] |
+ | |||
+ | [[File:ek-tm4c12gxl-board-setup.png |thumb|Tiva™ C Series TM4C123G LaunchPad]] | ||
− | |||
The [[EmSys:Tiva C Series TM4C123GXL Board | TM4C123GXL LaunchPad Board]] ICDI USB port (marked DEBUG and shown in the picture below) is a composite USB port and consists of three connections: | The [[EmSys:Tiva C Series TM4C123GXL Board | TM4C123GXL LaunchPad Board]] ICDI USB port (marked DEBUG and shown in the picture below) is a composite USB port and consists of three connections: | ||
*Stellaris ICDI JTAG/SWD Interface - debugger connection | *Stellaris ICDI JTAG/SWD Interface - debugger connection | ||
Line 16: | Line 17: | ||
*Stellaris Virtual Serial Port - a serial data connection | *Stellaris Virtual Serial Port - a serial data connection | ||
− | Using the included USB cable, | + | |
+ | Using the included USB cable, | ||
+ | * connect the USB emulation connector on your evaluation board (marked DEBUG) to a free USB port on your PC. | ||
+ | *: A PC’s USB port is capable of sourcing up to 500 mA for each attached device, which is sufficient for the evaluation board. | ||
+ | *: If connecting the board through a USB hub, it must be a powered hub. | ||
+ | * The drivers should install automatically. | ||
+ | |||
[[File:ek-tm4c12gxl-board-debug-switch.png |thumb|left|LaunchPad]]<br /><br /> | [[File:ek-tm4c12gxl-board-debug-switch.png |thumb|left|LaunchPad]]<br /><br /> | ||
Line 28: | Line 35: | ||
[[File:prev.gif|left|link=EmSys:Install TivaWare for C Series]][[File:next.gif|right|link=EmSys:Install ICDI Device Drivers]] | [[File:prev.gif|left|link=EmSys:Install TivaWare for C Series]][[File:next.gif|right|link=EmSys:Install ICDI Device Drivers]] | ||
--> | --> | ||
+ | |||
== Start == | == Start == | ||
*<big>Switch the '''POWER SELECT''' switch to the right for '''DEBUG''' mode.</big> | *<big>Switch the '''POWER SELECT''' switch to the right for '''DEBUG''' mode.</big> | ||
*<big>Connect the '''USB-A''' cable plug to an available port on the PC and the '''Micro-B''' plug to the Debug USB port on the Board.</big> | *<big>Connect the '''USB-A''' cable plug to an available port on the PC and the '''Micro-B''' plug to the Debug USB port on the Board.</big> | ||
*<big>Verify that the POWER LED D4 on the board is lit.</big> | *<big>Verify that the POWER LED D4 on the board is lit.</big> |
Revision as of 17:40, 6 April 2022
Hardware Setup
Kit Contents
You should find the following in your box:
- The TM4C123GXL LaunchPad Board
- USB cable (A-male to micro-B-male)
- README First card
Connecting the board
The TM4C123GXL LaunchPad Board ICDI USB port (marked DEBUG and shown in the picture below) is a composite USB port and consists of three connections:
- Stellaris ICDI JTAG/SWD Interface - debugger connection
- Stellaris ICDI DFU Device - firmware update connection
- Stellaris Virtual Serial Port - a serial data connection
Using the included USB cable,
- connect the USB emulation connector on your evaluation board (marked DEBUG) to a free USB port on your PC.
- A PC’s USB port is capable of sourcing up to 500 mA for each attached device, which is sufficient for the evaluation board.
- If connecting the board through a USB hub, it must be a powered hub.
- The drivers should install automatically.
Make sure that the power switch in the upper left hand corner of your board is in the right-hand DEBUG position as shown:
Start
- Switch the POWER SELECT switch to the right for DEBUG mode.
- Connect the USB-A cable plug to an available port on the PC and the Micro-B plug to the Debug USB port on the Board.
- Verify that the POWER LED D4 on the board is lit.