TM4C123 GPTM Interrupt Programming
Revision as of 05:17, 28 February 2018 by Jshankar
Timer Interrupt Programming
In the previous article, we showed how to program the timers. In those programming examples, we used polling to see if a timeout event occurred. In this section, we give interrupt-based version of those programs. Examine the earlier programs, we could run those programs only one at a time since we have to monitor the timer flag continuously. By using interrupt, we can run several of timer programs all at the same. To do that, we need to enable the timer interrupts using the GPTMIMR (GPTM Interrupt Mask) register.
Timers A and B Interrupt and Configuration Register Group
Six registers are used to control and handle interrupts of the Timers A and B:
- GPTM Interrupt Mask Register (GPTMIMR)
- GPTM Raw Interrupt Status Register (GPTMRIS)
- GPTM Masked Interrupt Status Register (GPTMMIS)
- GPTM Interrupt Clear Register (GPTMICR)
- GPTM Synchronize Register (GPTMSYNC)
- GPTM Peripheral Properties Register (GPTMPP)
GPTM Interrupt Mask Register (GPTMIMR)
|0||TATOIM||Timer A Time-out Interrupt Mask (0:interrupt is disabled, 1:interrupt is enabled)|
|1||CAMIM||Timer A Capture Mode Match Interrupt Mask (0:interrupt is disabled, 1:interrupt is enabled)|
|2||CAEIM||Timer A Capture Mode Event Interrupt Mask (0:interrupt is disabled, 1:interrupt is enabled)|
|3||RTCIM||RTC Interrupt Mask (0:interrupt is disabled, 1:interrupt is enabled)|
|4||TAMIM||Timer A Match Interrupt Mask (0:interrupt is disabled, 1:interrupt is enabled)|
|8||TBTOIM||Timer B Time-out Interrupt Mask (0:interrupt is disabled, 1:interrupt is enabled)|
|9||CBMIM||Timer B Capture Mode Match Interrupt Mask (0:interrupt is disabled, 1:interrupt is enabled)|
|10||CBEIM||Timer B Capture Mode Event Interrupt Mask (0:interrupt is disabled, 1:interrupt is enabled)|
|11||TBMIM||Timer B Match Interrupt Mask (0:interrupt is disabled, 1:interrupt is enabled)|
|16||WUEIM||32/64-Bit Wide GPTM Write Update Error Interrupt Mask (0:disabled, 1:enabled)|
IRQ21 is assigned to Timer1A and IRQ23 to Timer2A. The following will enable these timers in NVIC:
NVIC_EN0_R |= 0x00200000; /* enable IRQ21 */ NVIC_EN0_R |= 0x00800000; /* enable IRQ23 */
GPTM Raw Interrupt Status Register (GPTMRIS)
This 32-bit register only used the lower 10 bits to monitor and set a raw or internal interrupt if a GPTM-related raw interrupt occurred. These bits are set whether or not the interrupt is masked in the GPTMIMR register. However, whether these set raw interrupts can be sent to the interrupt controller to be further processed, it depends on whether the corresponding bits on the GPTMIMR register are set (enabled) or not (disabled). Only for those bits that have been set on the GPTMIMR register, they can be sent to the NVIC. The bit field and functions for this register are similar to those in the GPTMIMR register. If a GPTM-related raw interrupt is generated, the corresponding bit on this register is set to 1. Each bit can be cleared by writing a 1 to its corresponding bit in GPTMICR register.
Task 2: Build a General Purpose Timer Project.
Use GPTM block 0 Timer A (Timer0A) as a 16-bit count-down counter to periodically generate a timeout interrupt to turn on three LEDs, PF3∼PF1, via GPIO Port F. The input clock to the timer is the 16 MHz system clock, and the period to be counted in the Timer0A counter is 65.536 ms.
To perform this periodic interrupt for each 65.536 ms, one needs to:
- Enable and clock the Timer0A for GPTM Block 0.
- Enable and clock the GPIO Port B.
- Disable the Timer0A module before any configuration can be performed.
- Configure the Timer0A to work as a 16-bit count-down periodic counter.
- Load 65535 (65536 – 1) into the GPTMTAILR register as the start value since we want to get the maximum period of time, which is 65.536 ms, for each period.
- Load 15 (16 – 1) into the GPTMTAPR register as a prescale value. After this 16 MHz system clock is divided by this prescaler (16), the working clock for this counter is 1 MHz with a 1-μs period.
- Clear any previous timeout interrupt for Timer0A by writing 1 to an appropriate bit in the GPTMICR register.
- Enable Timer0A timeout interrupt by writing 1 to an appropriate bit in the GPTMIMR register.
- Use NVIC_PRI4_R (Bit 31 - 29 ) to set the interrupt priority level as 3 for the Timer0A.
- Use NVIC_EN0_R (IRQ19) to enable the timeout interrupt for the Timer0A.
- Enable the Timer0A module after these configuration and the Timer0A begins to count.
- Use EnableInterrupts() function to globally enable all interrupts.
- Use an infinitive while() loop to wait for any interrupt coming.
In addition to the main program, one also needs to build the Timer0A interrupt handler:
- Clear the timeout interrupt for Timer0A by writing 1 to an appropriate bit in the GPTMICR register to enable it to be generated in the future.
- Turn on the related LED via GPIO Port F.
Task 3: Use Timer1A and Timer2A timeout events to trigger interrupts.
- Configure Timer1A to timeout once every second. In the interrupt handler, toggle the red LED.
- Configure Timer2A to timeout at 10 Hz. In the interrupt handler, toggle the green LED.
- The infinite loop in the main program should blink the blue LED while the interrupts are going on.